In stock, ready to ship.
Factory style hidden winch kit!
Put your winch where it belongs: as close to center of gravity as possible, mounted directly to the frame, (not a bolted on bumper) and at the best possible point of leverage.
Bumper mounted winches are improperly mounted winches when it comes to the Montero / Pajero chassis. We said what we said, if you’re running a bumper mounted winch, you’re just setting yourself up for failure and heartache when you finally get stuck enough to need a properly mounted winch it will already be too late. We aren’t going to name names but competitors who put winches on their bumpers have photos of their bumpers ripped off the trucks when trying to recover from deep mud and large rocks where leverage and center of gravity pull really come into play. You don’t want to be that guy. Their bumpers are great, just not for winches. Think about it like this, if you were hanging from a cliff, would you prefer to rely on four 1/2 inch bolts bolting your winch and bumper to your frame holding you up, or would you prefer to be welded to a 3/8 inch thick plate with a carriage holding the winch in place, reinforced on the front and rear? The plate is the obvious answer but hopefully your never in that situation.
Before purchase: please READ THIS!
(Watch the install videos below as well.)
user installation required: Adequate welder and welding skills are
required to install! You're putting yours and other peoples' life at
risk if you do not properly install this! You may need to notch, grind,
drill or modify this plate slightly for your specific Montero - There's
not much walk-through information out there. This is a builder type
part. Take it to a fab shop or 4wd shop if you're uncertain. Most
mechanic shops wont touch something like this. Bad welds result in your
own risk, danger to others and just not good stuff, so be careful. we
aren't responsible for what you do with this thing.
first and only winch plate designed for ease of installation on the
Mitsubishi Montero in the US. Previously you could shop around and find a
winch plate close to what you needed, hack it up a whole bunch and then
retrofit it on your frame. This plate locates to the frame, with two
large holes that line up with the frame horns. Some of the tools
required to install this are a grinder and welder. Once complete your
winch will sit properly between the frame rails as Mitsubishi intended.
In other countries the Montero came with a winch from the factory. The
factory winch was PTO driven from the transfer case and mounted in the
same spot this plate is designed for.This results in a low CG pull that
will extract your truck from the most stuck situations. Other options
will have your winch up on a poorly mounted aftermarket bumper, putting
the pull at higher CG, more strain on the frame and more likelihood of
tearing a bumper mount. Slow and low, that is the tempo!
These plates are proudly designed and manufactured in America.
Some notes on our winch plate:
All frames are subjected to different elements and conditions, this plate has locating holes based off of factory trucks from Arizona that have never been subjected to corrosion or collision, your vehicle may have suffered any number of situation before your ownership, we do not guarantee this unit will fit perfect on every truck, it is far above and beyond anything you can get elsewhere in terms of a direct solution. Many hours of fitment testing and seeking out stock vehicles lacking damage brought this unit to the market. Please understand buying does not provide you with a simple bolt-in solution, if one could exist, we would've made it.
This thick steel plate is designed to locate to your frame, weld in
place and support most winches on the market. This winch plate is
designed to work with our skid plates, works with stock skid plates,
(some trimming may be required) and works well with our modular bumper
system on both the gen 1 and 2 Montero, Raider, Pajero and Galloper. Users who install without a
body lift can expect interference in the areas around the transmission
cooler, remote winch solenoid mounting is recommended. Check out the video
below for more detailed information on the fitment challenges when it comes to leaving the solenoid pack in place. It's quite common to relocate your winch solenoids to a more serviceable area. Gen 1 chassis owners that wish to keep their sway bar will need to use a cut off wheel to notch the back corner of the plate, this can be done in a way that reinforces the sway bar mount. Many of these vehicles lack sway bars by the time they're adding a winch. If you have any questions on this please contact us.
Hawaii, PR and international shipping is only available on the winch plate alone. If you need a complete winch kit outside of the contiguous United States, please contact us.
Warn 12k ZEON 12-S
12000 lbs winch with synthetic line and forged shackle.
Ideal for 3/4 and 1-ton pickups and all types of large frame rigs that
require longer and heavier pulls. The 12-S features IP68-rated
waterproof construction, an ultra-reliable Albright® contactor inside a
relocatable control pack, and a state-of-the-art, two-in-one remote for
added ease of use and versatility. With it’s fast line-speed and lower
amp draw, the 12-S winches are the hardest-working standard-duty
winches we’ve ever made,
with tactical styling that looks great up front and at a price that
won’t pull you out of your budget.
SmittyBilt Winch Specifications:
The Smittybilt X2O winches have been enhanced in almost every area for
increased performance and trouble free operation. Every X2O GEN3 winch
features a series wound 7HP motor that is completely sealed, as well as
all-new forged gears. The X2O line features a completely waterproof 500
AMP control box that can be mounted in 2 different locations.
All-new wireless controller with USB connectivity that can be wired to
the winch or unplugged for trouble-free wireless operation. The X2O also
features optimized gear ratios that deliver lightning- fast line
speeds. The X2O series comes standard with a synthetic winch rope for
Watch the above video all the way through to uncover a discount code on this part.
Watch the video below from Brian's page "In Z Mountains" to see even more detail on installing our winch plate:
ADHD Adventure Driven Hardcore Design - Weld-in American Made Winch Plate
- Brand: Adventure Driven Design
- Product Code: ADHDEWWK
- Availability: Out Of Stock
- Ex Tax: $135.00